Maxitrol Regulators

Maxitrol Regulators
  • RV-20LT 1/4″

    RV-20LT 1/4″

    SPECS:
    Size: 1/4″
    Capacity: 65000 BTU
    Fuel Type: Natural Gas, Propane

    These rubber seat poppet type regulators are designed primarily for main burner and pilot load applications where precise control of tiny flows is an essential operating requirement (.15 CFH).

    Housings are of high strength aluminum die castings. All models, with the exception of D suffix models, have been tested for multi-poise mounting and may be installed in any plane or angle without restriction. D suffix models are to be mounted horizontally. Other than normal upright position will result in slight difference of outlet pressure. They may be used with natural, manufactured, mixed, LP, or LP gas-air mixture.

  • RV-131 4″ FLGD

    RV-131 4″ FLGD

    SPECS:
    Size: 4″
    Capacity (BTU): 30000000
    Max Pressure: 2 psi

    FEATURES:
    – Greater accuracy – higher pressure drop capacity
    – Outlet pressures available to 42″ w.c.

    BENEFITS:
    – Provides bonus benefits of high capacity and good performance at pressures of 1 psi or higher
    – Unique conical valve design fills need of combining good regulation with high capacity in low to intermediate pressure range
    – Allows more pressure drop to be assigned to piping and valves – permits reduction in manifold size
    – Provides accurate, sensitive regulation at inlet pressures as low as 3″ w.c.
    – Ease of installation and replacement

  • RV-12LT 1/8″

    RV-12LT 1/8″

    1/8″ Poppet Style Gas Regulator – 30,000 BTU/h


    These rubber seat poppet type regulators are designed primarily for main burner and pilot load applications where precise control of tiny flows is an essential operating requirement. « certified (.15 CFH).
    Housings are of high strength aluminum die castings. All models, with the exception of D suffix models, have been tested for multi-poise mounting and may be installed in any plane or angle without restriction. D suffix models are to be mounted horizontally. Other than normal upright position will result in slight difference of outlet pressure. They may be used with natural, manufactured, mixed, LP, or LP gas-air mixture.

  • RV-111 2″ and 3″

    RV-111 2″ and 3″

    SPECS:
    Size: 2″, 3″

    All models except RV131 are CSA design certified for 1/2 psi rated pressure under the ANSI standard for gas pressure regulators; and CSA listed to certify compliance with nationally published safety, construction, and performance standards.

    They are main burner only, non-lockup type. They should not be used as a line gas pressure regulator ahead of low pressure controls. Use only where downstream controls can operate at line pressure. Refer to other Maxitrol sales bulletins for proper types. The RV52, RV53, & RV61 are suitable for multipurpose mounting. The RV81, RV91, RV111, & RV131 are recommended for normal horizontal position only.

  • 325-7AL : 1-1/4″ or 1-1/2″, Standard or with Vent Limiter

    325-7AL : 1-1/4″ or 1-1/2″, Standard or with Vent Limiter

    Available Sizes:
    1-1/4″ or 1-1/2″
    Note: This product is available for purchase with or without a vent limiter.

    The 325-7 is designed especially for the growing segment of electronic ignition equipment, permits the utilization of greater capacities without sacrificing performance. The 325 Series regulator is for use on residential, commercial, and industrial applications where adequate inlet pressures are available. They are a high performance type regulator and can be used as a single stage regulator – reducing pounds pressure to normal burner pressure.

  • 325-7A : 1-1/4″ or 1-1/2″, Standard or with Vent Limiter

    325-7A : 1-1/4″ or 1-1/2″, Standard or with Vent Limiter

    Available Sizes:
    1-1/4″ or 1-1/2″
    Note: This product is available for purchase with or without a vent limiter.

    SPECS
    Capacity (BTU): 1250000
    Size: 1-1/2″
    Capacity: 1250000 BTU

    The 325 Series is a pounds to inches regulator, meeting utility specifications. The 325 Series regulator is for use on residential, commercial, and industrial applications where adequate inlet pressures are available.

    They are a high performance type regulator and can be used as a single stage regulator – reducing pounds pressure to normal burner pressure. They can also be used as a line regulator on equipment already fitted with an appliance regulator.